Choosing tribology testing equipment often includes analyses of standardised procedures to be implemented in experimental techniques. This is why we present here a list of standard tests, which are possible with equipment, supplied by TTZH. However the requirements of our global customers and their internal standards could have a higher priority. If you don’t find a required test on our list, or would like to implement a new specific testing procedure, please don’t hesitate to contact TTZH Support and we would recommend you the best applicable tester, or include your technical task in development of absolutely new technique. Steady development and improvements is a subject of our dialogue and cooperation.
| ASTM B 611 | Test Method for Abrasive Wear Resistance of Cemented Carbides |
| ASTM D 1831 | Standard Test Method for Roll Stability of Lubricating Grease |
| ASTM D 1894 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| ASTM D 2266 | Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method) |
| ASTM D 2509 | Standard Test Method for Measurement of Load-Carrying Capacity of Lubricating Grease (Timken Method) |
| ASTM D 2596 | Standard Method for Measurement of Extreme Pressure Properties of Lubricating Grease (Four-Ball Method) |
| ASTM D 2670 | Standard Test Method for Measuring Wear Properties of Fluid Lubricants (Falex Pin and Vee Block Method) |
| ASTM D 2782 | Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Fluids (Timken Method) |
| ASTM D 2783 | Standard Method for Measurement of Extreme Pressure Properties of Lubricating Fluids (Four-Ball Method) |
| ASTM D 2981 | Standard Test Method for Wear Life of Solid Film Lubricants in Oscillating Motion |
| ASTM D 3233 | Standard Test Methods for Measurement of Extreme Pressure Properties of Fluid Lubricants (Falex Pin and Vee Block Methods) |
| ASTM D 3702 | Standard Test Method for Wear Rate of Materials in Self-Lubricated Rubbing Contact Using a Thrust Washer Testing Machine |
| ASTM D 3704 | Standard Test Method for Wear Preventive Properties of Lubricating Greases Using the (Falex) Block on Ring Test Machine in Oscillating Motion |
| ASTM D 4172 | Standard Test Method for Wear Preventive Characteristics of Lubricating Fluid (Four-Ball Method) |
| ASTM D 5183 | Standard Test Method for Determination of the Coefficient of Friction of Lubricants Using the Four-Ball Wear Test Machine |
| ASTM D 5706 | Standard Test Method for Measuring Wear Properties of Lubricating Greases using High Frequency Linear-Oscillating (SRV) Test Machine |
| ASTM D 5707 | Standard Test Method for Determining Wear Properties of Lubricating Greases using High Frequency Linear-Oscillating (SRV) Test Machine |
| ASTM D 6078 | Standard Test Method for Evaluating Lubricity of Diesel Fuels by the Scuffing Load Ball-on-Cylinder Lubricity Evaluator (SLBOCLE) |
| ASTM D 6079 | Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR) |
| ASTM D 6138 | Standard Test Method for Determination of Corrosion-Preventive Properties of Lubricating Greases Under Dynamic Wet Conditions (Emcor Test) |
| ASTM F 732 | Standard Practice for Reciprocating Pin-on-Flat Evaluation of Friction and Wear Properties of Polymeric Materials for use in Total Joint Prostheses |
| ASTM F 2661 | Standard Test Method for Determining the Tribological Behavior and the Relative Lifetime of a Fluid Lubricant using the Spiral Orbit Tribometer |
| ASTM G 65 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus |
| ASTM G 77 | Standard Test Method for Wear Resistance by Block-on-Ring Wear Test |
| ASTM G 99 | Standard Test Method for Wear Testing with a Pin-on-Disc Apparatus |
| ASTM G 105 | Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests |
| ASTM G 132 | Standard Test Method for Pin Abrasion Testing |
| ASTM G 133 | Standard Test Method for Linearly-Reciprocating Ball-on-Flat Sliding Wear |
| ASTM G 137 | Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-on-Ring Configuration |
| ASTM G176 | Standard Test Method for Ranking Resistance of Plastics to Sliding Wear using Block-on-Ring Wear Test—Cumulative Wear Method |
| ASTM G 181 | Standard Practice for Conducting Friction Tests of Piston Ring and Cylinder Liner Materials Under Lubricated Conditions |
| BS 903:Part A61 | Physical Testing of Rubber: Determination of the Frictional Properties of Rubber |
| BS EN 1071-6 | Advanced technical ceramics. Methods of test for ceramic coatings. Determination of the abrasion resistance of coatings by a micro-abrasion wear test |
| BS EN 1071-12 | Advanced technical ceramics. Methods of test for ceramic coatings. Reciprocating wear test |
| CEC F-06-A-96 | Diesel Engines - Diesel Fuel - Performance Requirement and Test Method for Assessing Fuel Lubricity |
| CEC L-45-T-93 | Viscosity Shear Stability of Transmission Lubricants (Taper Roller Bearing Rig) |
| DEF STAN 91-110/1 | Wear Performance Test for Aqueous Polyglycol Based Hydraulic Fluids |
| DIN 50324 | Measuring Friction and Wear: Model Experiments on Sliding Friction in Solids (Ball on Disc System) |
| DIN 51350 Part 6 | Testing Lubricants: Testing in the Shell Four-Ball Tester - Testing of Shear Stability of Lubricating Oils Containing Polymers |
| DIN 51350 Parts 1-5 | Testing Lubricants: Testing in the Shell Four-Ball Tester |
| DIN 51802 | Testing Lubricants: Testing of Lubricating Greases to Corrosion Preventing Properties. SKF EMCOR Method |
| DIN 51813 | Testing Lubricants: Determination of Content of Solid Matters in Greases |
| DIN 51819 | Testing Lubricants: Mechanical-Dynamic Testing on the Bearing Lubricant in Tester FAG FE8 |
| DIN 51821 | Testing Lubricants: Testing of Lubricating Greases in Tester FAG FE9 |
| IP186/93 | Determination of Low Temperature Torque of Lubricating Grease |
| IP 220/67 | Determination of corrosion inhibiting properties of lubricating greases (SKF Emcor method) |
| IP 239 | Extreme Pressure Properties: Friction and Wear Test for Lubricants: Four-Ball Machine |
| IP 300 | Rolling Contact Fatigue Tests for Fluids in a Modified Four Ball Machine |
| ISO 11007 | Petroleum products and lubricants - Determination of rust-prevention characteristics of lubricating greases |
| ISO/CD 11008 | Petroleum Products and Lubricants - Determination of Extreme Pressure Properties of Lubricating Greases - Four Ball Method |
| ISO/DIS 12156-2 | Diesel Engines - Diesel Fuel - Performance Requirement and Test Method for Assessing Fuel Lubricity |
| ISO/DIS 7148-2 | Plain Bearings - Testing of the Tribological Behaviour of Bearing Materials |
| JASO M 349-2001 | Test Method for Anti-Judder Performance of Automatic Transmission Fluids |
| MIL-G-10924 | Military Specification: Grease, Automotive and Artillery |
| NPT 60-185 | Determination of corrosion inhibiting properties of lubricating greases (SKF Emcor method) |
| SIS 155130 | Determination of corrosion inhibiting properties of lubricating greases (SKF Emcor method) |
